GEO/IGSO混合区域导航星座的设计与优化算法

区域导航星座能够以较低成本和较短时间获得目标区域导航能力，且地球同步轨道是构建非极区区域导航星座的重要轨道类型。提出一种基于GEO（地球静止轨道）和IGSO（倾斜地球同步轨道）的区域导航星座设计方法。基于星下点轨迹特性构造对称星座设计参数和优化参数集，并考虑地球扁率长期摄动影响，计算星座轨道参数。以导航服务区的统计GDOP（几何精度因子）为目标函数，利用差分进化算法构建星座优化模型。以印度IRNSS的7星星座为例，仿真检验了设计和优化算法的正确性，讨论了IRNSS星座优化构型和轨道类型选取。本方法采用的对称星座设计参数少，能够提升GEO/IGSO混合区域导航星座的全局优化效率，为后续非对称星座快速提供最佳星数和构型设计。     

多等级区域侦察弹性星座设计方法

针对传统侦察星座目标单一、弹性低的问题，提出了多等级区域侦察弹性星座的设计方法。该方法将星座设计过程按区域等级信息分为多个子星座逐步设计，直到整体星座对所有的区域性能满足设计要求。以区域被划分为3个等级为例，首先对星座设计需求、设计指标及设计步骤进行了分析。其次推导了地面最低分辨率和轨道高度的关系并确定了不同子星座的轨道高度。最后考虑轨道倾角、一箭多星发射、光照和升交点漂移同步约束，构建基础星座、子星座1和子星座2的优化模型。最终设计星座为3层混合星座，共8个轨道面和70颗卫星，星座对各等级区域的最大重访时间分别为10937s，12241s和17437s，弹性指数为2213%，2420%和6361%。结果表明该方法设计的星座可实现对区域覆盖和弹性分级的设计要求，证明了方法的有效性。对比Walker星座设计方法，在同等设计要求下，Walker星座所需卫星数为156颗，多等级区域侦察弹性星座所需卫星数远低于Walker星座，结果进一步证明了该星座设计方法的优越性。     

A progressive approach to predict shot peening process parameters for forming integral panel of Al7050-T7451

In this paper, a progressive approach to predict the multiple shot peening process parameters for complex integral panel is proposed. Firstly, the invariable parameters in the forming process including shot size, mass flow, peening distance and peening angle are determined according to the empirical and machine type. Then, the optimal value of air pressure for the whole shot peening is selected by the experimental data. Finally, the feeding speed for every shot peening path is predicted by regression equation. The integral panel part with thickness from 2 mm to 5 mm and curvature radius from 3200 mm to 16000 mm is taken as a research object, and four experiments are conducted. In order to design specimens for acquiring the forming data, one experiment is conducted to compare the curvature radius of the plate and stringer-structural specimens, which were peened along the middle of the two stringers. The most striking finding of this experiment is that the outer shape error range is below 3.9%, so the plate specimens can be used in predicting feeding speed of the integral panel. The second experiment is performed and results show that when the coverage reaches the limit of 80%, the minimum feeding speed is 50 mm/s. By this feeding speed, the forming curvature radius of the specimens with different thickness from the third experiment is measured and compared with the research object, and the optimal air pressure is 0.15 MPa. Then, the plate specimens with thickness from 2 mm to 5 mm are peened in the fourth experiment, and the measured curvature radius data are used to calculate the feeding speed of different shot peening path by regressive analysis method. The algorithm is validated by forming a test part and the average deviation is 0.496 mm. It is shown that the approach can realize the forming of the integral panel precisely.     

一种基于VPL 的元器件快速建模方法

为了更好地落实航空电子模块的可制造性设计审查工作,结合航空电子模块产品特点和技术要求,建设了基于Valor软件的PCB/PCBA设计与检测自动化分析系统.元器件模型库作为该系统的必要组成部分,其覆盖范围和数据精度对审查结果至关重要.本文将从元器件模型库建设必要性、建设过程和建模工艺要求三个方面进行阐述,并提出一种基于Valor VPL的元器件快速建模方法,应用结果表明,该方法能够高效构建满足系统审查精度的元器件模型,使大规模元器件模型库的建设成为可能.     

A novel framework for liquid propellant engine’s cooling system design by sensitivity analysis based on RSM and multi-objective optimization using PSO

One of the challenges of combustion chamber and nozzle design in a Liquid Propellant Engine (LPE) is to predict the behavior and performance of the cooling system. Therefore, while designing, the optimization of the cooling system is always of great importance. This paper presents the multi-objective optimization of the LPE’s cooling system. To this end, a novel framework has been developed, resulting from the application of the Response Surface Method (RSM) and the correlation coefficients matrix, sensitivity analysis and the The Particle Swarm Optimization (PSO). based on this method, the input variables, constraints, objective functions, and their surfaces were identified. In terms of multi-optimization algorithms, RSM and PSO are utilized to get global optimum. In conclusion, the methodology capability is to optimize the LPE’s cooling system, 6 percentage increase in total heat transfer and 7 bar decrease cooling system pressure loss, which resulted in a 1.2-seconds increase in the specific impulse of the engine.     

Development and performance evaluation of tropospheric scintillation model on Ku-band satellite link over Akure,Nigeria

Existing amplitude scintillation prediction models often perform less satisfactorily when deployed outside the regions where they were formulated. This necessitates the need to evaluate the performance of scintillation models developed in one region using data data from other regions while documenting their relative errors. Due to its variation with elevation angle, frequency, other link parameters and meteorological factors, we employed three years (January 2016 to December 2018) of concurrently measured satellite radio beacons and tropospheric weather parameters to develop a location-based amplitude scintillation prediction model over the Earth-space path of Akure (7.17^oN, 5.18^oE), South-western Nigeria. The satellite beacon measurement used Tektronix Y400 NetTek Analyzer at 1 s integration time while meteorological parameters, namely; temperature, pressure and relative humidity were measured using Davis Vantage Vue weather station at 1 min integration time. Comparative study of the model’s performance with nine (9) existing scintillation prediction models indicates that the best and worst performing models, in terms of root mean square error (RMSE), are the Statistical Temperature and Refractivity (STN) and direct physical and statistical prediction (DPSP) models with values 11.48 and 51.03 respectively. Also, worst month analysis indicates that April, with respective enhancement and fade values of 0.88 and 0.90 dB for 0.01% exceedance, is the overall worst calendar month for amplitude scintillation.     

插装式液控能源选择阀的设计与分析

针对液压系统油源的安全性及可靠性问题，提出油源冗余设计方法，即多油源供给多负载，当某一油源发生故障时能源选择阀切断故障油源，由其他油源给负载提供基本液压能源，系统能完成必须的服役性能。针对液压系统能源选择阀存在的频繁换向与振动问题，提出一种插装式液控能源选择阀，其先导阀采用锥阀和可变阻尼形式，主阀采用三台肩且终端有缓冲功能的滑阀。建立了插装式液控能源选择阀的数学模型，分析了能源选择阀在两种模拟故障下的切换压力及切换时间、油源压力脉动等特性。理论分析结果表明，油源压力阶跃和线性变化时，某能源选择阀切换时间分别为5 ms和7 ms。当压力发生波动时，主阀不会发生振动，还可通过液控先导阀结构设计来控制切换压力和回复压力大小。     

SABRE预冷器计算模型及其在整机模型中的应用

预冷器的性能对SABRE等预冷组合循环发动机具有重要影响,为实现发动机方案设计阶段预冷器的快速设计与评估,建立了预冷器准二维快速评估模型。将SABRE预冷器的几何结构简化为一个扇环形区域,沿径向和周向将该区域划分为二维节点。应用守恒方程及传热关联式完成单个节点计算,再求解节点矩阵的平衡方程组,计算内外流体特定节点上参数的二维分布,得到预冷器出口参数。将模型嵌入发动机总体性能程序中,实现了发动机设计及非设计点的预冷器性能计算的功能。与文献数据对比结果表明,预冷器模型传热计算误差小于5%,摩擦阻力误差小于10%。整机计算结果显示,Ma0~5范围内,预冷器空气侧温降范围为143K至932K,温降随飞行马赫数升高单调上升。预冷器传热有效度范围为0.896-0.945,空气侧总压恢复系数范围为0.852-0.904。     

SiC/CVD SiC复合涂层的抗氧化及抗热震性能研究

为了提高C/SiC复合材料耐高温性能,采用泥浆浸渍裂解与真空化学气相沉积(CVD)在材料表面制备了SiC/CVD SiC复合涂层,通过XRD、SEM分析了涂层组成与结构;研究了复合涂层的高温抗氧化(700～1 500℃)和抗热震性能。结果表明,泥浆浸渍法制备的SiC涂层具有一定的封孔效果,可使材料开孔率下降,但高温抗氧化效果并不佳,1 200℃氧化10 min后材料弯曲强度保留率下降明显仅有86%。CVD SiC涂层结构致密,与SiC封孔涂层结合较好,在700～1 500℃具有较好的抗氧化效果,随着氧化温度的升高,氧化后涂层完好,表面O元素逐渐增加,材料失重率缓慢增加但不大于0.5%,且材料性能并未下降。涂层材料在1 200℃-10 min短时热震5次后材料弯曲强度保留率仍有95%以上,且未出现开裂、剥落等热震损伤。在1 200℃-30 min长时热震10次后,涂层材料基本被完全氧化,材料失去保护作用,弯曲强度下降至90%左右。     

并联机器人运动性能的研究现状及发展趋势

随着并联机器人技术的发展,其运动性能的提升成为了发展需求,指出了研究工作空间和奇异位形的必要性。以研究方法为主线,详细阐述了工作空间和奇异位形的国内外研究现状及特点,进一步提炼出个体的创新思想和面临的共同难题。通过深入分析研究方法的原理,找到了解决共同难题的突破口,同时剖析了研究中的尚存难题。结合未来的发展趋势,从结构综合和理论创新两个方面进行突破,能够为并联机器人的发展提供强劲动力。得出的结论和展望给从事这一领域的研究者们提供了参考。